Top 5 Best 3D Printers Under $5000

It must be frustrating not to know where to look for the Best 3D Printers Under $5000. We know that buying 3D printers is not the easiest task in the world. The market is full of copies and products that should never have been invented. One bad turn and you could easily get a worthless 3D printer that is never worth $5000. We are here to help. In this guide to the best 3D printers under $5000, we show you the only 3D printers you need to take seriously.

Please note that we have set our minimum price at $1000 because we do not want to roam in a cheap area. We have sorted our main choices in the table below to make the choice easier. Let’s take a look at the best 3D printers under $5000 in our comparison chart, then we’ll discuss it one by one.

Best 3D Printers Under $5000 Comparison Table

3D Printers Under $5000
Printer NameConnectivityWeight
Raise3D N2 PlusWi-Fi, USB, SD card143.3 lb
Robo 3D R2USB, Wifi30.2 lb
LulzBot TAZ 6USB, SD Card33 lb
MakerGear M2eUSB, SD Card26.5 lb
MakerBot Replicator PlusUSB, Wifi40.4 lb

Here are the Top 5 Best 3D Printers Under $5000

Raise3D N2 Plus

If you can afford it, the Raise3D N2 Plus is one of the best 3D printers under 5000 dollars. Forget the big 3D printers whose maximum height is 10 inches. Choose a 3D printer that doubles more than this limit. Introducing the Raise3D N2 Plus, the best 3D printer you can get for less than $5000. It’s a huge 3D printer that far surpasses the other major 3D printers on the market, including the popular MakerBot Replicator Z18 and the second highest 3D printer on the list, the Robo 3D R2. The N2 Plus is a fully enclosed 3D printer. It is housed in a sturdy aluminum frame with a transparent shade that allows you to quickly monitor your progress.

Top 5 Best 3D Printers Under $3000

Everything is stuck in the box, with no dangerously prominent parts and rough threads to grasp. It is natural that the N2 Plus has an integrated interface larger than normal. It has a 7-inch touch screen interface right next to it. It is responsive, easy to navigate and contains simple options that beginners can easily understand. In total, the design of the N2 Plus is clean, robust, functional and aesthetic. With a dual extruder configuration (a single extruder configuration is also available), the N2 Plus is a reliable workhorse that can print non-stop days with consistent results. Overall, this is one of the best 3D printers under $5000.

Pros:

  • Fantastic print quality across the board
  • Fully enclosed for temperature consistency
  • Easy to set up and requires minimal calibration
  • Print resume feature
  • Easy-to-use touchscreen interface
  • Low noise level while printing

Cons:

  • Default software isn’t the most beginner-friendly

Check Price

back to menu ↑

Robo 3D R2

The Robo 3D R2 is one of those 3D printers that can be easily sold at a price twice as high and escaping without being called “too expensive”. It’s so good. So maybe you want to resume before Robo 3D suddenly decides to raise the price because it’s too good a deal. Resulting from a successful campaign on Kickstarter, the R2 is a large 3D printer looking like a miniaturized time machine, straight out of a sci-fi movie. It is one of the best 3D printers under 5000 dollars. It is closed on all sides except at the top where the filament comes from the spool pin located at the back.

But even with the top uncovered, the regulating power of the R2’s temperature is still good. The R2 arrives almost assembled, with only a few components to install. It has a heated construction panel, which should be good news for anyone who wants to play with ABS. In addition, the construction plate has an excellent standard adhesion, so you will not have to resort to tricks such as the use of glue or tape. The R2 also has a built-in camera for remote monitoring.

The most impressive feature of the R2 is the 5-inch touch screen interface located at the bottom of the machine. It’s not just an interface. This is a unique hub that allows you to do a number of things that make 3D printing easier and easier. More importantly, the touch screen interface contains cutting software that allows you to prepare your 3D models without the aid of a computer. The built-in slicing software is not exactly the complete package, but it is quite suitable for basic tasks. Overall, this is one of the best 3D printers under $5000.

Pros:

  • Excellent print quality
  • Compatible with third-party filaments
  • Generous build size for the prize
  • Intuitive touchscreen interface
  • Onboard slicer and built-in memory
  • Integrated camera for remote monitoring

Cons:

  • High noise level
  • Not fully enclosed on all sides

Check Price

back to menu ↑

LulzBot TAZ 6

If you are a handyman, you need a 3D printer with which you can play and how you want. No machine in this price range is more open to DIY than the LulzBot TAZ 6, one of the most popular and one of the best 3D printers under 5000 dollars. The TAZ 6 is an open-frame 3D printer that arrives largely assembled. There is no need to install it from the base, although it is a 3D DIY printer based on promotional images. It is maintained by a sturdy aluminum frame that keeps it stable during printing. It contains an integrated interface, located at the top of the power supply box.

It’s just a simple LCD interface, so do not expect too much. Similar to the LulzBot Mini, the TAZ 6 requires a little DIY in the initial setup process. The leveling of the bed is simple and the software installation is quick and easy. It takes about an hour to get it out of the box, install the parts, review the initial configuration and load the starting filament. If you’ve ever used 3D printers, especially DIY 3D printers, setting the TAZ 6 takes only about 30 minutes.

Top 5 Best 3D Printers Under $1000

One of the main reasons why the TAZ 6 is so easy to install is the supplied manual. This is one of the most complete and detailed manuals we have ever seen in this price range. It’s possible to go through the first install without looking at the help videos on YouTube, which says a lot. If you manage to use your TAZ 6, everything should be a walk in the park. It is easy to use and includes a user-friendly Cura software that allows you to print your first 3D model in just a few minutes. Overall, this is one of the best 3D printers under $5000.

Pros:

  • Quick and easy initial setup
  • Detailed instruction manual
  • User-friendly default software
  • Superb print quality
  • Large build size
  • Low noise level for an open-framed 3D printer

Cons:

  • No enclosure
  • Rudimentary built-in interface
  • Not Wi-Fi compatible

Check Price

back to menu ↑

MakerGear M2e

Not impressed by the LulzBot TAZ 6? If you want the second best open-frame 3D printer in this price range, you do not have to look any further than the MakerGear M2e. It is almost comparable to TAZ 6, with only a few differences that prevent our choice from being the best price. Like the TAZ 6, the M2e is largely assembled. It’s also easy to set up, with an initial setup of about 30 minutes, perhaps less for veterans doing 3D printing. It has everything you need in one of the best 3D printers under 5000 dollars.

The print quality of the M2e is comparable to that of the TAZ 6. It is polished, precise and detailed. If you buy both and print the same items with exactly the same settings and support, you probably can not tell which one. The M2e is also equipped with a heated construction plate and is perfectly capable of working with different types of filaments, including ABS, Flexible and PETG. Now let’s talk about what differentiates the M2e from the TAZ 6. If you pay attention to the comparison chart above, you will first notice that the MakerGear M2e has a building volume below the TAZ 6.

It is even larger than many other 3D printers in this class and is therefore not in the category of mini-3D printers. The smaller M2e construction plate is the main reason why we opted for the TAZ 6. The M2e is louder than the TAZ 6. It is not extremely noisy. Moving parts emit only more mechanical sounds, which can be a problem if you have M2e on your desktop. Overall, this is one of the best 3D printers under $5000.

Pros:

  • Fantastic print quality
  • Easy to set up
  • Sturdy and stable construction
  • Easy to calibrate
  • Excellent after-sales support
  • Open-source hardware and software

Cons:

  • Non-enclosed
  • Noisy
  • Instruction manual could be improved

Check Price

back to menu ↑

MakerBot Replicator Plus

MakerBot is one of the most recognizable brands in the industry. Many 3D printers are cloning MakerBot products, and the Replicator Plus is the latest addition to the list. The Replicator Plus is an open-frame 3D printer housed in a shiny case. It is one of the best 3D printers under 5000 dollars. He has this undeniable high-end look that shouts: “I’m expensive!” It contains a camera embedded on one of the pillars and a nice integrated reel holder at the back. It has a color LCD interface, which at first seems really cool until you realize that it is operated by a button.

In terms of design, the Replicator Plus has the same professional look as other MakerBot 3D printers. This is a rugged machine that fits any office, although we do not recommend placing it in your bedroom or office, as it can be very noisy and annoying. The Replicator Plus is designed to enable easy and problem-free 3D printing, especially for beginners. He usually comes assembled. Connecting all disconnected parts takes only a few minutes. The first installation is even easier.

It is installed via the MakerBot application on your smartphone, which you must of course first download, as well as the MakerBot printing software. Once Replicator Plus is set up, you must then view MakerBot Print, MakerBot’s own printing software. It is a user-friendly software with simple and clear options. Unless you are having serious problems with program navigation, you need to understand MakerBot Print without any problem. Overall, this is one of the best 3D printers under $5000.

Pros:

  • User-friendly software
  • Onboard camera for remote monitoring
  • Large build plate
  • Prints faster than predecessor
  • Filament jam detection and auto-pause
  • Filament run-out notifications

Cons:

  • No heated build plate
  • Built-in spool holder not compatible with third-party spools
  • Needs MakerBot filaments for best results

Check Price

Final Words

3D printers are an amazing invention that materializes your imagination projects. you can draw what you want. In this article, we mentioned some of the Best 3D Printers Under $5000 that you can buy right now in the market. As this is not a cheap investment, we recommend that you check all possible details before choosing one. And if you have questions about what to choose, do not hesitate to contact us at any time.

Top 10 Best 3D Printers Under $500

We will be happy to hear your thoughts

      Leave a reply

      For security, use of Google's reCAPTCHA service is required which is subject to the Google Privacy Policy and Terms of Use.

      I agree to these terms.

      Tech Gadget Guides
      Login/Register access is temporary disabled